FixLivity is reader-supported. We may earn an affiliate commission when you buy through the links on our site. Learn more.
I’ve been using a Crosley dryer for the past two years. It’s been working perfectly. For us, our dryer was a lifesaver. Despite being a costly purchase, the dryer has proven to be a wonderful investment. However, my Crosley dryer is not heating.
Why is my Crosley dryer not heating up? When I opened the dryer vent to check the interior, I realized that the Crosley dryer not drying clothes on a typical cycle owing to clogged vents. I promptly grabbed my dryer vent airflow meter and used a dry vacuum cleaner to clean out the vents. My problems were rectified, and my dryer was as good as new.
I’ve observed that my dryer has been malfunctioning for a few weeks. There wasn’t enough heat and Crosley dryer not turning on. I couldn’t believe such an issue could exist in a dryer that was only two years old. But it didn’t bother me. I was well aware of the issue as an appliance repair technician.
Tools and materials needed to fix a Crosley dryer not heating are given below:
List of Problems That Might Cause Your Crosley dryer to troubleshoot
- Clogged vents
- Defective cycling thermostat
- Broken circuit breakers
- Faulty main circuit board
- Worn out dryer timer
Solutions on How to Fix a Crosley dryer not heating up
1. clogged dryer vents
The operation of your clothes dryer is dependent on the dryer vent or duct. The dryer will not be able to dry your clothes without it, and there is a substantial risk of fire. Installing a dryer vent correctly, keeping it clean, and diagnosing small issues are all simple, low-cost, and necessary ways to ensure that your dryer works effectively.
Wet clothing is tumbled through heated air in a spinning drum by clothes dryers. This hot air evaporates the moisture, takes it up, and pushes it out of the dryer with the help of a fan. Not only that but the dryer’s damp air is carried to the house’s outside via the vent. A 4-inch diameter metal vent on the back of every dryer exhausts the water-laden air.
You won’t be able to blow this air into your home’s interior with most dryers. A flexible, semi-rigid, or rigid tube transports air from the dryer to the outside. This tube has one end that connects to the dryer and the other end that connects to a hole created in the house’s side.
The factor that could cause the Crosley gas dryer not to heat up because of clogged dryer vents. This could lead to a slew of other issues in your dryer. If you neglect this problem for too long, your dryer will break down.
What happens if the vents on your dryer become clogged? Due to a clogged vent, the airflow of your dryer is decreased. As a result, the airflow of the dryer is obstructed. Because hot air is trapped within your dryer, it is overheating. Cleaning your dryer vents and removing any lint, dirt, or blockages is the simplest way to ensure that your dryer is working properly.
Solutions
The following instructions to solve the issue are given below:
- Remove the dryer from the outlet.
- Determine where your dryer vent is located.
- To connect dryers, a compact 4-inch diameter exhaust pipe is generally employed.
- This pipe is used to link ductwork within a wall.
- Once you’ve found it, look inside your dryer exhaust vent for any debris, such as dust, lint, or even dirt.
- Remove any obvious barriers and clear any obstructions with a vacuum.
- Test the dryer out and make sure it works properly
2. Defective cycling thermostat
The cycling thermostat is in charge of turning on and off the dryer’s heat source to maintain a target temperature specified by a timer or a temperature selection button. The dryer’s cycling thermostat is a bi-metal thermostat that works almost every time.
This thermostat is normally closed, enabling unrestricted passage of electricity. When the dryer heats up, the thermostat will open, breaking electrical contact with the heat source and allowing the drum temperature to drop somewhat, forcing the thermostat to close and reenergizing the heat source.
If the thermostats in your dryer fail, they will no longer be able to heat. This is why your dryer is not heating. A malfunctioning cycling thermostat could be to blame if your electric dryer isn’t properly performing the Auto Dry cycle. This part controls the temperature of the dryer as well as the operation of the timer motor on Auto Dry versions.
So how to change the heating element in the Crosley dryer? To change a heating element in your dryer you will need to use a multimeter. Set your multimeter to the RX 1 setting to test the thermostat’s resistance. Connect the probes of the meter to the wire terminals.
A reading of 0 should be obtained. A low or near-zero resistance indicates that the electrical flow is good. On the other hand, if the number is high your thermostat probably needs replacing.
Solutions
The following ways to replace your defective cycling thermostat are given below:
- Unplug the dryer from the power outlet
- Remove the screws from the back panel
- Remove the back panel
- Disconnect the wires from the cycling thermostat
- Remove the mounting screw and slide the cycling thermostat out of the slot
- Install the new cycling thermostat and reinstall the mounting screw
- Reconnect the wires
- Reinstall the back panel
- Test the dryer out and make sure the timer works without any issues.
3. Broken circuit breakers
If none of the other options work, it’s possible that your dryer’s circuit breakers are to blame. A circuit breaker is a type of electrical switch that protects a circuit against damage caused by overcurrent, overload, or short circuit.
The basic function of protective relays is to stop current flow when they detect a problem. Due to heavy use, dryer circuit breakers may become worn out over time. This weakens them, leading them to trip often and resulting in insufficient heat from dryers.
How do you check the circuit breaker on a dryer? The most effective way is to turn off and on the dryer breakers. One may trip, in which case the dryer will run on 120 volts but won’t be able to heat the clothes. The problem is most likely with the thermostat or element if the breakers are in excellent working condition and the dryer is running.
Solution
The following are the steps to changing the circuit breakers in your dryer:
- At the top of the panel, turn off the power to the service panel.
- Remove the lid from the service panel to inspect the circuit breakers.
- Confirm the disconnection of electricity with a two-prong electrical tester.
- Unscrew the two set screws that secure the black and red wires in the breaker and pull the black and red wires out from under them.
- Remove the circuit breaker from the service panel.
- A 30-amp double pole breaker should be used in place of the circuit breaker.
- The black and red wires should be reconnected and placed beneath the two set screws at the rear of the breaker
4. Faulty main circuit board
The control board of your dryer’s major duty is to maintain the machine functioning properly, from setting the time to regulating the temperature. As a result, if your dryer’s main control board malfunctions, it may produce too much heat. Your dryer’s circuit breaker trips, causing the machine to come to a halt.
So, how can you know if your control panel is still in good working order? To gain access to your dryer’s primary control board, remove the top panel. Examine the board for any signs of damage. Any existing signs may need to be replaced. If none of the other options work, the problem could be with your dryer’s main control board.
Solution
To replace the main circuit board, follow the steps below:
- Unplug the dryer and turn off the gas.
- By moving the dryer away from the wall, you can get it out of the way.
- Remove the screws with a 1/4″ nut driver
- Pull the top panel back slightly to remove the tabs behind the console. Pull the dryer’s top panel up and away from the machine.
- With a slot screwdriver, remove the locking tabs from the wire connectors. Remove the wire harness plug from the connection port on the electronic control board.
- Remove one hex head screw using a 1/4″ nut driver. Slide the electronic control board out of the slots in the support brackets.
- Replace the control board with a new one after removing it.
5. Worn Out The Dryer Timer
One of the most important components of a dryer is the dryer timer. It regulates many aspects of the dryer, most notably the power. The dryer and the timer engine are also controlled by the timer. Along these lines, if this is harmed or worn, it could be the primary cause of your Crosley dryer timer not working.
When things start to go wrong, the best thing to do is make another part. When you’ve figured out your model number, you’ll be able to set up a proper timer for your component. Turning it off is one of the most important things you can do before replacing the dryer element. It’s also a good idea to turn off the circuit breaker as an extra layer of protection against electric shock.
Solution
The following ways to replace a dryer timer are given below:
- Remove the dryer from the power socket
- Begin by removing the large handle on the dryer’s front, then disclosing the dryer section, which houses the timer.
- This is usually found on the top backboard, however, different models have different placements. The wires attached to the timer should then be removed.
- They’re usually color-coded, but to double-check that you’ve reattached everything correctly, it could be a good idea to take a photo with your camera phone.
- When you’re done with the elderly, look for signs of consumption, angling, or other problems. If these problems persist, the terminals should be replaced.
- You can proceed to remove the wires in any case, using the long-nose pincers for difficult wire associations.
- You can reattach the new timer and the button on the dryer’s facade once the linkages are replaced as they should be.
- When you plug the dryer back in, the problem with the dryer spinning erratically should be resolved.
Frequently Asked Questions
1. Why is my dryer running but not heating?
A tripped circuit breaker, clogged vent, or no gas flow are all common causes of a dryer, not heating. Check these components and repair or replace them if necessary.
2. How do I reset my Crosley dryer?
The machine can be reset by disconnecting or turning off the dryer. To reset the dryer, press and hold the Start / Pause button for five seconds while it is turned off. Then switch the device back on to see if the code is still present.
3. Where is the thermal fuse located on a Crosley dryer?
The fuse is positioned on the blower housing or at the heat source of the dryer, which is usually the heating element on electric dryers or the burner on gas dryers.
4. How do you change a heating element in a Crosley dryer?
Out of the Crosley dryer cabinet, remove the heating element canister. To detach the heating element within the canister, turn it clockwise. Remove the element from the canister by sliding it out. In the canister, slide the new heating element in.
5. How do I know if my thermal fuse is blown?
Touch the right side of your multimeter lead to the right side of the fuse to see if it has blown, then repeat with the left multimeter lead. If the multimeter needle stays stationary, the thermal fuse has blown.
6. Why is the dryer blowing cold air?
One of the most common reasons your tumble dryer decides to pump out chilly air instead of hot is that it has overheated, which is hilarious. Manufacturers are required by law to ensure that when your dryer gets too hot, it has some sort of safety feature to prevent it from catching fire.
Conclusion
Due to clogged vents, my Crosley dryer was not heating. I was worried that I would need to buy a new dryer. These days, dryers are simply too pricey for me to afford. However, I was able to laugh it off after deconstructing it. I felt relieved and let out a huge breath. The vents in my dryer were the source of my dryer heating problem.
Many others, like myself, are having similar problems. They may not have as much experience as I have, but they may be equally concerned about their dryers. As a result, I’ve compiled a list of concerns and possible remedies to assist those facing similar issues.
As a frequent user of dryers and an appliance repair specialist, I can honestly claim that my dryer is one of the best purchases I’ve ever made. Allowing minor flaws to sway your opinion of how fantastic something is is a mistake.
However, I strongly suggest you turn off the power before beginning any of the troubleshooting approaches. It will safeguard you from electrocution, which could result in the dryer failing.
