FixLivity is reader-supported. We may earn an affiliate commission when you buy through the links on our site. Learn more.
While drying my clothes, I noticed my dryer had grown dirty over time, so I decided to clean it. As I was cleaning the dryer, I was trying to figure out how to remove front panel of Maytag dryer? I was worried at first, but as an appliance technician, I decided to handle the situation on my own.
So, what issues did I encounter while removing the front panel of my Maytag dryer? It was because due to years of usage my screws got rusted for which I was having a hard time removing the front panels of the dryer. How did I resolve the issue? I simply changed the rusted screws with new screws which resolved my issues. Because of this convenience, I was struggling to remove the Maytag dryer front panel clips.
I quickly grabbed my toolbox and removed the screws from the bottom of the panel and I found out that because of years of usage, the screws got rusted for which I was having a hard time removing them. I replaced the screws and reinstalled the panel and it solved my problem.
Step by step solutions on how to remove front panel of Maytag dryer is given below:
Types of front panels in a dryer are given below:
- Upper front panel
- Lower front panel
1. Upper front panel
An upper front panel is usually located at the back of the dryer depending on the type of dryer you have. Front panels can be used to detect problems within the dryer and it is the first thing to remove while solving an issue with the dryer.
The Maytag clothes dryer’s front panel is designed like a goal post. To unclip the panel, grab the slim upper sides and wiggle them back and forth. Lift the front panel of the bottom clips by pulling the skinny ends of the front panel toward you. Remove the front panel and set it aside.
By removing the front panel, you’ll have access to components that need to be repaired or replaced frequently. Of course, the exact procedures for removing the front panel will vary depending on the model of Maytag dryer you have but usually, the front panel is located at the back of the dryer.
Solutions
The following ways how to remove the front panel of a Maytag front load dryer are given below:
- Disconnect the power switch of the dryer
- Remove the screws from the front panel using a 1/4-inch nut driver
- Rotate the upper front panel from the top to release the wire clips at the top
- Disconnect the wire harness from the door switch
- Remove the retaining clip from the top of the panel
- The front panel of the dryer has been successfully removed and set aside.
2. Lower front panel
Depending on the model of dryer you have, the lower front panel is normally positioned toward the bottom of the dryer. Front panels can be utilized to detect faults within the dryer, and they are the first thing to remove when troubleshooting a problem.
To remove the lower front panel insert a flat-head screwdriver in the gap between the lower panel. In the gap between the upper and lower front panels of the dryer, insert a flat-head screwdriver or putty knife. To detach the lower dryer panel, depress the two spring clips. The lower panel should be removed.
You’ll have access to components that need to be repaired or replaced frequently by removing the lower front panel. Of course, the exact steps for removing the front panel will differ based on the Maytag dryer model you have, but the lower front panel is normally found in the back of the dryer.
Solutions
The following ways how to remove the front bottom panel of the Maytag dryer are given below:
- Disconnect the power switch of the dryer
- Remove the screws from the front panel using a screwdriver
- Rotate the upper front panel from the top to release the wire clips at the top
- Disconnect the wire harness from the door switch
- Remove the retaining clip from the top of the panel
- The front panel of the dryer has been successfully removed and set aside.
FAQs
1. How do you disassemble a Maytag dryer?
To disassemble a Maytag dryer first remove the power switch of the dryer and your next step is to remove the screws located at the bottom of the front panel and then set aside the panel. Next, remove the screw cap from the drum cabinet to release it and then disconnect the belt and pull the belt out and then lift out the drum to gain full access to the dryer and the Maytag dryer will be disassembled.
2. How do I open my dryer?
Unplug the dryer and turn off the power before opening the top or front doors. Remove the lint filter and two screws on the side of the lint filter aperture by lifting the top lint filter and a solid front panel.
3. How do you put the front panel on a dryer?
To put the front panel on a dryer first reinstall all the wires which were disconnected, rotate the front panel to reinstall it, and reinstall the screws.
4. How do you take the front panel off a Whirlpool dryer?
Insert a flat-head screwdriver or putty knife into the gap between the upper and lower front panels of the dryer. Depress the two spring clamps on the lower dryer panel to take the front panel off a whirlpool dryer.
5. How do you get the lint out of the bottom of a dryer?
Start by cleaning the lint filter before each load to get rid of the lint in your dryer. Remove the lint by hand or by soaking the filter in water. Remove the back panel and exhaust hose from your machine after unplugging it. Wipe clean the inside and exhaust sections of your dyer using a vacuum and a cloth.
Conclusion
My concern grew when I was unable to open the front panel, at the same time I was also concerned about my dryer. However, after realizing the problem, I was able to laugh off the matter. Rusted screws were the source of the problem. My dryer is as good as new thanks to my knowledge as an appliance repair specialist and a few dollars.
Not only me but almost every dryer owner has faced complications regarding how to remove the front panel of a Maytag dryer. There’s no need to be concerned if you run into a problem like this. By following the troubleshooting options I’ve provided above, you should be able to solve this problem quickly.
As a person who relies significantly on dryers as well as an appliance repair technician, I must say that my dryer is one of the best purchases I’ve ever made. Don’t allow minor flaws to sway your opinion of how excellent this item is.
