Kenmore Dryer Not Spinning

4 Reasons Why Kenmore Dryer Not Spinning – how to fix it?

FixLivity is reader-supported. We may earn an affiliate commission when you buy through the links on our site. Learn more.

Being newly married, my wife and I travel everywhere. We love traveling. It feels like we’re running down through our clothes faster than ever. It’s also tiring to do laundry, so we usually dump them into a basket until we feel like putting them in the washing machine. But the washing machine isn’t all. After everything’s been washed thoroughly, I put it in the dryer.

But that day, I noticed a strange thing with my Kenmore dryer. It wasn’t spinning properly. So, why wasn’t my Kenmore dryer not spinning? Turns out, it was just a faulty door switch. Being an appliance repair technician has helped me instantly replace the switch with a new one. Now, you may also face such problems with your Kenmore dryer. But, no worries, I have a simple solution for you. So, come along with me if you want your Kenmore dryer up and running!

Tools You need to fix Kenmore Dryer Not Spinning Issues

To assist you in this DIY project, you will require the following tools:-

List Of the Problems For Kenmore Dryer Not Spinning Is Given Below:

Solutions For Spinning Issues

Your Kenmore dryer might not be spinning due to issues such as the following:-

  1. Faulty door switch
  2. Worn idler pulley
  3. Worn out drum support roller
  4. Broken drum belt

Step By Step Solutions For Spinning Issues With Your Kenmore Dryer Are Given In The Following:

1. Faulty door switch

A door switch is direct on/off the part that blocks the dryer from working when the door is kept open. Dryer door switches are a little over an inch long. It will be arranged around the door opening on the front board. You may have the choice to pop the switch clumsily or dispense with it by wiping out only a singular screw.

As a security highlight, the dryer won’t work in an entryway. At the point when the switch is broken, it can’t perceive the control board that the door is closed, so the dryer won’t turn on. The best way to let you know if the switch is flawed is to remove it from the dryer and test it with a multimeter.

Solution

The steps below will instruct you on how to replace a faulty door switch:-

  1. Turn off the dryer. Assuming it’s a gas dryer, shut off the gas.
  2. Pull the build-up screen out of the lodging in the top board of the dryer.
  3. Utilize a Phillips screwdriver to eliminate the 2 screws that solid the build-up of the screen lodging to the top board.
  4. Raise the top board.
  5. Utilize an opening screwdriver to deliver the locking tab on the wire tackle plug for the door switch.
  6. Eliminate the door switch
  7. Embed the new door switch and secure it with the mounting screws.

2. Worn idler pulley

The idler pulley in your dryer is fundamental for keeping up with strain on your dryer drive belt while it folds over the drum to prevent the belt from slipping. On the off chance that the idler pulley doesn’t work as expected, then, at that point, your dryer can make a shrieking commotion.

How would you check for a free idler pulley? Start by turning off your dryer and eliminating the front access board. The idler pulley and shaft are close to the drive engine. After eliminating the belt, physically turn the pulley. On the off chance that it doesn’t pivot without a hitch, you ought to supplant the pulley and shaft.

Solution

To replace an idler pulley, follow the steps below:

  1. Turn off the dryer. If it’s a gas dryer, shut off the gas. Wear work gloves to ensure your hands.
  2. Utilize a Phillips screwdriver to eliminate the 2 screws that solid the build-up screen lodging to the top board.
  3. To deliver the clasps that lock the highest point of the dryer set up, push a clay blade under the cover close to the left and right edges of the front of the dryer.
  4. Lift the top and prop it safely against the divider behind the dryer.
  5. Utilize a 5/16-inch nut driver to eliminate the front board mounting screws from within the dryer.
  6. Haul the idler pulley out of the section in the foundation of the dryer.
  7. Introduce the idler pulley in the section at the foundation of the dryer and string the drive belt onto the new idler pulley.
W10837240 Dryer Idler Pulley with Bracket by Seentech - Exact Fit for Whirlpool Kenmore Dryer...
  • ✅ MODEL NUMBER: W10837240 Dryer Idler Pulley with Bracket. Replaces part number: 3387372, 3388674, W10118754, W10118756, W10547287, W10547290, W10837240VP
  • ⚙️ COMPATIBLE BRANDS: Whirlpool Jenn-Air Amana Magic Chef Admiral Inglis Norge Sear Kenmore and others. ✅ FIT MODELS. Whirlpool: 3CSP2760BN0, 3CSP2760BW0, 3CSP2761BN0, 3CSP2761BW0, 3CSP2761BW1, 3LWED4800YQ0. Kenmore: 10687884100, 10687884300, 10687884600, 11060052990, 11060052991, 11060056990. Amana: 4KAED4900BW0, 4KAED4900BW1, 4KMEDC100BQ0, 4KNED4400BQ0...
  • ✅ PREMIUM QUALITY: The replacement part is made from durable high quality material and well-tested by the manufacturer, Meets OEM standards - Ensure long-lasting and effective performance.

3. Worn out drum support roller

Drum bearings are the bearings found at the front of the drum of the dryer. So how can it respond? The drum support bearings on the front board of the drum permit the drum to pivot flawlessly when it is turning. On the off chance that the drum bearings are exhausted or are broken, you should supplant them with new ones.

All in all, how might you recognize exhausted or broken bearings inside your dryer? A screeching or shrieking commotion from within the dryer is one of the principal signs of exhausted or broken dryer bearings. Loss of oil prompts warming up and changing their shape because of loss of grease.

Solution

To replace the broken drum of the dryer bearings, proceed with the steps below:

  1. Separate the power supply string from the dryer outlet. Pivot the gas valve to the “off” position assuming your dryer uses gas for heat.
  2. Open the bureau to eliminate the drum of the dryer, and access the bearing.
  3. Look along the back divider inside the dryer bureau for the back drum support bearing and section.
  4. Eliminate one screw from the back drum support bearing section.
  5. Search for the little metal ball in the back mass of the first nylon support bearing.
  6. Eliminate the screw from the contrary side of the bearing help section.
  7. A glimpse inside the drum of the dryer to locate the three screws situated at the focal point of the drum of the dryer divider.
  8. Reinstall your drum from the dryer, and reassemble the bureau by switching your dismantling steps.

4. Broken drum belt

A long, flimsy drive belt inside your dryer helps turn the drum and is often time known as the drum belt. Rehashed utilization of this drum belt makes it exhausted. This causes a sharp and bothering screeching clamor from inside the dryer. How to look for a well-used drum belt? To look at a well-used drum belt on your dryer, eliminate the front board of the dryer to access and check for any mileage. Assuming that you notice any indications of wear, you might need to supplant them.

Solution

To replace the drum belt within your dryer, commence with the following steps:-

  1. Turn off the dryer. On the off chance that it’s a gas dryer, shut off the gas.
  2. Pull the build-up screen out of the lodging in the top board of the dryer.
  3. Utilize a Phillips screwdriver to eliminate the 2 screws that protected the build-up screen lodging to the top board.
  4. Utilize a space screwdriver to deliver the locking tab on the wire saddle plug for the entryway switch. Separate the wire tackle.
  5. Utilize a 5/16-inch nut driver to eliminate the front board mounting screws from within the dryer.
  6. Position the new drive belt on the drum of the dryer. Lift the front of the drum to get to the drive engine and idler pulley.
  7. String the drive belt onto the idler pulley.
  8. Push the idler pulley to one side and circle the drive belt over the engine pulley.
BlueStars 341241 Dryer Drum Belt Replacement Part - Exact Fit for Whirlpool Kenmore Dryer - Replaces...
  • ✅ 𝟏𝟎𝟎% 𝐋𝐈𝐅𝐄𝐓𝐈𝐌𝐄 𝐖𝐀𝐑𝐑𝐀𝐍𝐓𝐘: Customer satisfaction is our priority. If for any reason you're not completely satisfied, we will compensate you and offer extra benefits to ensure your rights. Buy with confidence!
  • ✅ PREMIUM QUALITY: The replacement part is made from durable high-quality rubber and well-tested by the manufacturer - Ensure long-lasting and stable performance. The 341241 Multi Rib Belt is 1/4" wide, and 92 1/4 inches in length, features 4 ribs and 3 grooves. Please check the model number carefully before ordering. You can send us your dryer model number, we will help you confirm if it fits or not.
  • ✅ HIGH COMPATIBILITY: It is made exactly fit for most top name brands (Whirlpool, Kenmore, KitchenAid, Roper, Norge, Maytag, Magic Chef, Crosley, Admiral, Estate, Amana, Inglis, Jenn-Air, Hoover). This part works with the following models: 1LE5700XKW0, 1LG5701XKW0, 2LG5701XKW0, 3LE5700XKW0, 3LE5710XKW0, 3LE5710XMW0, 3LE5710XMW1, 3LE5710XMW2, 3LG5701XKW0, 3LG5701XPW0, GEN2000HQ1, GEN2000HZ1, GEQ8858HQ1, GEQ8858HZ1, GLE7900XKW0, WED4815EW1, NED4655EW1, AED4675YQ1, PYE4500AYW, etc.

Frequently Asked Questions

1. How would you fix a Kenmore dryer that can’t warm?

If your Kenmore dryer is not drying, then it might be because of a faulty heating element.

2. For what reason is my dryer running yet not warming?

A broken thermostat might be a reason why your dryer is running but not warming up.

3. Is it true or not that there is a reset button on a Kenmore dryer?

Many models have a reset button, but many dryers do not!

4. How can I say whether my dryer warm circuit is blown?

To check for a blown thermal fuse, you will need a multimeter.

5. For what reason is my Kenmore dryer blowing cold air?

Your Kenmore dryer might be blowing cold air because of its faulty heating element.

6. Would a dryer be able to in any case dry without heat?

A dryer will still be able to dry without hearing, but it will take a lot of time.

7. How would you fix a dryer that isn’t warming?

To fix a dryer that isn’t warming, you will need to replace the blown thermal fuse.

Conclusion

My Kenmore dryer is a rather expensive one! My wife and I had planned out thoroughly while buying this dryer. It took quite a lot of finance to even consider buying it. But after using it for almost two months, when it stopped spinning, I got scared. But being an appliance repair technician, my experience has taught me to remain calm and think about the problem.

And that’s what I did. I had replaced the door switch and the problem just vanished! Now, everyone might not be an appliance repair technician like me. To help you guys, I have described every possible issue and how to fix them. Follow these and you will be able to fix your dryer. Good luck!

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top
Scroll to Top